MPAE-18454: readme bugfix

Author: ChaddFrasier-mchp

.main-meta/main.json

@@ -4,7 +4,7 @@
     "content": {
         "metaDataVersion": "1.3.0",
         "name": "com.microchip.mcu8.mplabx.project.pic18f56q24-cnano-8bit-mdfu-client-mplab-mcc",
-        "version": "1.2.0",
+        "version": "1.2.1",
         "displayName": "Getting Started with the 8-Bit MDFU Client for PIC18F56Q24",
         "projectName": "pic18f56q24-cnano-8bit-mdfu-client-mplab-mcc",
         "shortDescription": "GitHub Example for the 8bit MDFU Client Library using PIC18F56Q24 with a CNANO board.",

README.md

@@ -35,7 +35,7 @@ This example demonstrates:
 
 - PIC18F56Q24 Curiosity Nano [(EV01E86A)](https://www.microchip.com/en-us/development-tool/ev01e86a)
 
-[![PIC18F56Q24_CNano](images/230928-MCU8-PHOTO-EV01E86A-Front-Transparent.png)](images/230928-MCU8-PHOTO-EV01E86A-Front-Transparent.png)
+[![PIC18F56Q24_CNano](images/230928-mcu8-photo-ev01e86a-front-transparent.PNG)](images/230928-mcu8-photo-ev01e86a-front-transparent.PNG)
 
 ## Setup
 
@@ -138,9 +138,9 @@ This section is consistent for any example created in this repository.
 **Clock And Configuration**
 - Set the clock and configuration bits to the same values that were set in the MDFU Client
 
-[![CLK](images/ClockSetup_App.PNG)](images/ClockSetup_App.PNG)
+[![CLK](images/ClockSetup_App.png)](images/ClockSetup_App.png)
 
-[![CFG](images/ConfigBitsSetup_App.PNG)](images/ConfigBitsSetup_App.PNG)
+[![CFG](images/ConfigBitsSetup_App.png)](images/ConfigBitsSetup_App.png)
 
 **I/O Pins**
 - GPIO Input: RF3

spi/Readme.md

@@ -21,20 +21,20 @@
 - I/O Pin Entry: Enabled
 - Memory Verification: CRC32
 
-[![MDFU](../images/MDFUClientSetup_SPI.PNG)](../images/MDFUClientSetup_SPI.PNG)
+[![MDFU](../images/MDFUClientSetup_SPI.png)](../images/MDFUClientSetup_SPI.png)
 
 **SPI**
 - Custom Name: SERCOM
 - BOOT_CONFIG: Mode 0
 - Interrupt Driven: Disabled
 
-[![SPI](../images/SPIDriverSetup.PNG)](../images/SPIDriverSetup.PNG)
+[![SPI](../images/SPIDriverSetup.png)](../images/SPIDriverSetup.png)
 
 **MSSP1 PLIB**
 - Serial Protocol: SPI
 - Enable Client Select: Enabled
 
-[![SPI_PLIB](../images/SPIPLIBSetup.PNG)](../images/SPIPLIBSetup.PNG)
+[![SPI_PLIB](../images/SPIPLIBSetup.png)](../images/SPIPLIBSetup.png)
 
 **SPI Pins**
 - MSSP SCK: RC1
@@ -43,7 +43,7 @@
 - MSSP SS (Chip Select): RA5
     - Custom Name: CHIP_SELECT
 
-[![SPI_Pins](../images/SPIPortsSetup.PNG)](../images/SPIPortsSetup.PNG)
+[![SPI_Pins](../images/SPIPortsSetup.png)](../images/SPIPortsSetup.png)
 
 **8-Bit MDFU Client I/O**
 - BOOT INDICATE: RF2
@@ -60,7 +60,7 @@
 - ROM Ranges: This option is configured based on the start address of the application
 - For example, if the application starts at 0x2000 then this value will reflect as `0-1FFF`
 
-[![IO-Settings](../images/ProjectProperties_SPI.PNG)](../images/ProjectProperties_SPI.PNG)
+[![IO-Settings](../images/ProjectProperties_SPI.png)](../images/ProjectProperties_SPI.png)
 
 ### Application Setup
 Refer to the [Application Setup](../README.md#application-setup) section in the main Readme file.
@@ -82,11 +82,11 @@ This example shows how to execute the CRC32 verification example and update the
 
 3. Right click, then select **Clean and Build**.
 
-[![CleanBuild](../images/CleanAndBuildMDFU_SPI.PNG)](../images/CleanAndBuildMDFU_SPI.PNG)
+[![CleanBuild](../images/CleanAndBuildMDFU_SPI.png)](../images/CleanAndBuildMDFU_SPI.png)
 
 4. Program the MDFU client project.
 
-[![ProgramMDFU](../images/ProgramMDFU_SPI.PNG)](../images/ProgramMDFU_SPI.PNG)
+[![ProgramMDFU](../images/ProgramMDFU_SPI.png)](../images/ProgramMDFU_SPI.png)
 
 **Bootloader Operation After Initial Programming**
 
@@ -109,7 +109,7 @@ After initial programming, the LED must be on.
 
 Right click, then select Clean and Build
 
-[![CleanBuild_App](../images/CleanAndBuildApp_SPI.PNG)](../images/CleanAndBuildApp_SPI.PNG)
+[![CleanBuild_App](../images/CleanAndBuildApp_SPI.png)](../images/CleanAndBuildApp_SPI.png)
 
 4. Build the Application Image File using [pyfwimagebuilder](https://pypi.org/project/pyfwimagebuilder/).
 
@@ -124,7 +124,7 @@ Below is an example of the command used in the above step.
 
 `pyfwimagebuilder build -i "application_hex_file.hex"  -c "mdfu_config_file.toml" -o output.img`
 
-[![build_img](../images/BuildTheImage_SPI.PNG)](../images/BuildTheImage_SPI.PNG)
+[![build_img](../images/BuildTheImage_SPI.png)](../images/BuildTheImage_SPI.png)
 
 > **Tip**: The configuration TOML file is generated by the MDFU Client project.
 
@@ -144,7 +144,7 @@ Below is an example of the command used in the above step.
 
 `pymdfu update --tool mcp2210 --image ./output.img --chip-select 7 --clk-speed 50000`
 
-[![transfer_img](../images/SendTheImage_SPI.PNG)](../images/SendTheImage_SPI.PNG)
+[![transfer_img](../images/SendTheImage_SPI.png)](../images/SendTheImage_SPI.png)
 
 **Application Has Been Updated Successfully**